ARM Power V4.02  (Tue Oct  1 13:48:43 PDT 2024)
1.	OpenSSL: 3.0.13 30 Jan 2024 (Library: OpenSSL 3.0.13 30 Jan 2024)
2.  	Apache Version: 2.4.59 
3.  	Openssh: 9.8p1
4.  	NET-SNMP Version: 5.9.1	
5.  	OpenVPN Version: 2.5.7	
6.  	IPSec Version: 5.9.8/K5.4.0	
7.  	Bash Version: 5.0.0(1)-release	
8.  	IPSEC/OPEN VPN: Allows for Multiple tunnels to work at the same time.
9.  	WEB GUI allows for the creation of an SNMP V3 user with the following special character: @
10. 	API calls allows for the creation of a password using the “&” character to match the CLI
11. 	Login Banner allows for the use of the following special character: * 
12. 	Network Parameters can now be changed from Web GUI
13. 	Inactivity Timeout can now be set on the WEB Interface
14. 	API Calls added for VPN, SSL CERTS, & Plug Group Action
15. 	CVE-2023-48795 Terrapin Vulnerability has been resolved by the upgrade of OpenSSH to 9.8 p1
16. 	CVE-2024-6387 regreSSHion Vulnerability has been resolved by the upgrade of Open SSH to 9.8 p1
17. 	Access Level using Radius Duo using Cisco ISE and Web GUI now assigning correct permissions without signing into CLI first
18. 	UseSTARTTLS/UseTLS option has been added in Use TLS in Email messaging
20. 	Hostname field added under system parameters
21. 	User Defined Prompt added under Scripting options
22. 	Command prompt now supports "user defined prompt"
23. 	U-boot/default added for product under command prompt
24. 	Fixed issue where HTTPS issue where web is enabled but not able to launch web session
25. 	Fixed: Email messaging was not working if site-id was configured on the unit.
26. 	Fixed: LDAP was not working if site-id was configured on the unit.



Obtaining Firmware Updates:

The most recent updates for our Console Server, Switched PDU and Data Fallback products can be found by visiting https://www.wti.com/pages/software

For older firmware updates, please contact WTI Tech Support at service@wti.com, call our toll free service line at 1-888-280-7227, live chat or fill out a software request form at https://www.wti.com/pages/software

Customer Service Department hours are 8 AM through 5 PM, Pacific Daylight Time.



Installation:

NetReach Centralized Management Software (NetReach), is the preferred method for installing firmware updates on WTI devices.  The NetReach software allows you to manage firmware updates for multiple WTI units from a single interface. 

For a description of the process for managing firmware updates via the NetReach, please refer to the NetReach user's guide, which can be downloaded from the WTI User's Guide Archive at:

https://www.wti.com/pages/manuals-documentation

Note that in order to use the NetReach software, the existing firmware version for the WTI Device(s) must conform to the following standards:

•	Console Server Products (DSM, CPM, and REM Series):  Firmware Version 7.04 or higher.  
•	Switched PDU Products (VMR, NBB, NPS and RPC):  Firmware Version 3.03 or higher.

When upgrading older units that are running firmware versions that are earlier than the standards listed above, it is recommended to use the WTI Centralized Management Software (WMU).  The WMU can be downloaded from WTI's FTP server, located at:

https://www.wti.com/products/wmu-centralized-management-software

Please refer to the WMU user's guide for further instructions.

In addition to the NetReach and WMU, the /UF command can also be used to install firmware upgrades.  For more information on the /UF command, please refer to the user’s guide for your WTI device.